manualshive.com logo in svg

Garmin Cessna Caravan G1000, Руководство по линейному обслуживанию

Поделиться
Скачать
Garmin Cessna Caravan G1000 Скачать руководство пользователя страница 25

______________________________________________________________________________

____________________________________________________________________________

LMM for the Kodiak 100

Page 2-9

190-02102-00 Rev.4

2.2.13   GTS 800 Traffic System

The GTS 800 is a microprocessor-based Line Replaceable Unit (LRU) that uses active 
interrogations of Mode C transponders to provide Traffic Advisories to the pilot. When 
installed with a 1090 MHz ADS-B transmit class of equipment, the GTS 800 also utilizes 
passive surveillance. Traffic is displayed on the MFD via ARINC 429 and/or Ethernet 
High Speed Data Bus (HSDB). 

An aural alert is also provided to inform the crew a traffic advisory (TA) will be displayed. 
A top mounted directional antenna is used to derive bearing of the intruder aircraft, which 
is displayed with relative altitude to own aircraft. Top antenna transmitted interrogations 
are directional, reducing the number of transponders that receive the interrogation, thus 
reducing potential garble on the 1090 MHz band.

Optional bottom antenna transmit interrogations are directional antenna (recommended 
for retractable gear installations). A bottom directional antenna installation gives the 
benefit of intruder bearing visibility for targets that are shaded from the top directional 
antenna.

2.2.14   GWX 75 Airborne Weather Radar Processor

The Airborne Weather Radar is an all-digital, high definition radar that automatically 
performs multiple scan/sweep angles to help give the actual size, shape and hazardous 
storm cell activity. It has zero blind range for close-in returns and ground clutter 
suppression. It provides data to the PFDs and to the MFD.

2.2.15   GWX 70R Weather Radar

The GWX 70R is a solid-state weather radar providing airborne weather and ground 
mapped radar data to the PFDs and to the MFD. The displays communicate with the 
GWX 70R weather radar through a high-speed data bus (HSDB) Ethernet connection.

NOTE

R stands for Reduced Scan. It has a 45-degree scan as opposed to ±60
degrees with hard mechanical stops. 

2.2.16   GDL 69A SXM Satellite Radio Receiver

The GLD 69A SXM is a satellite radio receiver that provides data link weather 
information to the MFD (and, indirectly, to the inset map of the PFD) as well as digital 
audio entertainment. The GDL 69A SXM communicates with the MFD via a HSDB 
connection. Subscriptions to the SiriusXM Weather or SiriusXM Satellite Radio services 
are required to enable the GDL 69A SXM capability. 

Uncontrolled if Printed

Содержание Cessna Caravan G1000

































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды