Garmin Cessna Caravan G1000 Скачать руководство пользователя | Manualshive

Страница: 208 / 288

background image

______________________________________________________________________________

____________________________________________________________________________

Page 5-10

LMM for the Kodiak 100

190-02102-00 Rev.4

5.2.10 GTS Traffic System

Unit Part Number: 011-01356-00

GTS 8XX Installation Manual: 190-00587-00

GTS 8XX Maintenance Manual: 190-00587-01

1. To remove:

a) If a cooling hose is attached to the unit, remove it from the air fitting and set

aside.

b) Turn the harness connector jackscrews counterclockwise to disengage them

from the unit.

c) Pull the harness connectors away from the unit.

d) Disengage the QMA coax connectors by pulling back firmly on the outer

sleeve of the QMA plug away from the jack connector. This will disengage the
locking mechanism that secures the plug connector to the jack connector.
Pulling on or disengaging the QMA connectors in any other way is not
recommended and may cause damage to both the connectors and coaxial
cable.

e) Loosen the unit hold down clamp by turning it counterclockwise until it disen-

gages the unit hold down tab.

f) Pull the unit up slightly at an angle and pull the unit out of the rack from the

connector end of the unit.

2. To reinstall:

a) Hold the unit at a slight angle with the connector end up and slide the back of

the unit into the rack engaging the curled-up lip at the back of the rack.

b) Fully seat the unit the rest of the way into the rack.

c) Pull the locking clamp up and turn it clockwise to engage the unit hold down

tab tightly.

d) Attach the QMA coax connectors by holding the outer sleeve of the QMA plug

to align the connectors and insert the plug onto the jack until it snaps into
place. There will be an audible ‘snap’ when the connectors are fully engaged.
No tools are required for the insertion of a QMA plug onto a QMA jack.

e) Install the harness connectors and tighten the connector jackscrews to secure

the connectors.

f) If a cooling hose was attached to the unit, reinstall the cooling hose to the air

fitting.

Uncontrolled if Printed

«
...
206
207
208
209
210
...
»

Содержание Cessna Caravan G1000

































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Cessna Caravan G1000

GPSMAP 400 series

Бренд: Garmin Страницы: 28

Бренд: Garmin Страницы: 136

Бренд: Garmin Страницы: 16

Cirrus Perspective SR20

Бренд: Garmin Страницы: 128

Approach G5 - GPS-Enabled Golf Handheld

Бренд: Garmin Страницы: 168

Бренд: Garmin Страницы: 2

Бренд: Garmin Страницы: 2

Cessna Caravan G1000

Бренд: Garmin Страницы: 482

Бренд: uAvionix Страницы: 54

Бренд: Tecfrigo Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды