manualshive.com logo in svg

Garmin Cessna Caravan G1000, Руководство по линейному обслуживанию

Поделиться
Скачать
Garmin Cessna Caravan G1000 Скачать руководство пользователя страница 261

______________________________________________________________________________

____________________________________________________________________________

LMM for the Kodiak 100

Page 7-35

190-02102-00 Rev.4

27. If the bearing is not as anticipated, recheck the antenna coaxial connections by 

verifying the following:

•  QMA connectors are 'snapped' firmly in place.
•  Connections are made to the proper channels and color-coded heat shrink is 

the same color on both ends of cable QMA connectors are correctly installed 
on cables.

•  Correct antenna type is selected in the configuration.

NOTE

If multiple targets are displayed during the antenna tests, recheck the
antenna coaxial connections.

7.10   GWX Processor Testing

Perform an operational check by pressing each softkey on the Map-Weather Radar 
Screen (MFD-normal mode) for the proper operation of each function (see 

Figure 7-13

). 

Ensure no abnormal or non-working annunciations or messages are displayed on the 
MFD Weather Radar Screen when testing each softkey. Refer to the Kodiak Pilot's Guide 
for a complete description of the GWX features and operation using the softkeys.

Figure 7-13.  Weather Radar Screen

Uncontrolled if Printed

Содержание Cessna Caravan G1000

































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды