Galaxy Hunter Series Скачать руководство пользователя

Страница: 79 / 200

Parameter

Description

IP Version

Select

IPv4

IPv6

IP Address

When you select

Static

Mode

, enter the IP address and subnet

mask that you need.



IPv6 does not have subnet mask.



The default gateway must be in the same network segment with

the IP address.

Subnet Mask

Defaut Gateway

Preferred DNS

IP address of the preferred DNS

Alternate DNS

IP address of the alternate DNS

Enable ARP/Ping

to set IP address

service

Select the check box, get the camera MAC address, and then you can

modify and configure the device IP address with ARP/ping command.

This is enabled by default. During reboot, you will have no more than 2

minutes to configure the device IP address by a ping packet with

certain length, the server will be turned off in 2 minutes, or it will be

turned off immediately after the IP address is successfully configured. If

this is not enabled, the IP address cannot be configured with ping

packet.

A demonstration of configuring IP address with ARP/Ping.

1. Keep the camera that needs to be configured and the PC within the

same local network, and then get a usable IP address.

2. Get the MAC address of the camera from device label.

3. Open command editor on the PC and enter the following command.

4. Reboot camera.

5. Check the PC command line, if information such as

Reply from

192.168.0.125…

is displayed, the configuration succeeds, and you

can turn it off then.

6. Enter http://(IP address) in the browser address bar to log in.

Step 3 Click

Save

Содержание Hunter Series









































































































































































































Результаты поиска

Содержание Hunter Series

Отзывы:

Похожие инструкции для Hunter Series

Бренды по названию

Популярные бренды

Galaxy Hunter Series, Руководство пользователя

Результаты поиска

Содержание Hunter Series

Отзывы:

Похожие инструкции для Hunter Series

Бренды по названию

Популярные бренды