Fukuda Denshi DS-8400, Руководство по обслуживанию

Страница: 25 / 274

xxi
not be displayed.
 If the HR/PR source is set to [SpO
2
], and if SpO
2
waveform/numeric data is set to [Disp. OFF], the PR value
will not be displayed.

If the RR source is set to [CO
2
/GAS], and if CO
2
waveform/numeric data is set to [Disp. OFF], the RR value
will not be displayed.
 If the RR source is set to [CO
2
/GAS], and if GAS waveform/numeric data is set to [Disp. OFF], the RR value
will not be displayed.
 Do not set the same remote control ID to multiple monitors in the same floor. Otherwise, the remote control
operation may control multiple monitors at the same time.
 After the remote control setup, check that the remote control unit is properly operating.
 If the time/date is not correctly set, or changed during monitoring, malfunction may occur with NIBP
measurement, periodic printing, trend, NIBP list data, and age calculation from the birth date.
 If the time/date is changed, the time/date for all the saved patient data (trend, list, recall, etc.) will also change.
The printed time/date before changing and the displayed time/date after changing will differ.Also, the data
transmitted to the central monitor before the time/date is changed will be displayed on the central monitor with
the previous time/date.
Precautions about the Multigas Unit Data Monitoring (MGU-800/MGU-810 Series)
 When the multigas unit (MGU-800/MGU-810 series) and HPD-800/HPD-810/HPD-820, HCP-800/HCP-810/
HCP-820 are simultaneously used, the CO
2
concentration measurement will be performed by the equipment
selected for the "CO
2
Source Priority" under ( [Menu] > "Parameter" [CO
2
]) .

The MGU-800/MGU-810 series require warm up of about 10 minutes to correctly measure the data.
 If the power supply is interrupted due to power failure, etc., MGU-800/810 series multigas unit will initialize
and enter into warm-up mode even if the power interruption is within 30 seconds.
 About the Gas Calibration
The gas calibration will automatically start when the MGU-800/810 series multigas unit is connected.
After the warm-up completes, gas calibration will be performed every 4 hours during stable operation.
During warm-up, gas calibration interval will become shorter than during normal operation.
During gas calibration, measurement data will not be updated.
Calibration gas is not required during gas calibration.

Dispose of calibration gas according to the regulation of each medical institution.
 Make sure the sampling line and flow sensor is securely connected to prevent any leakage.
 The gas leakage inside or outside the equipment will cause measurement error. Make sure to check for leakage
before usage.
 An environment with alcoholic vapor may adversely affect the measurement readings.
 CO
2
, N
2
O or anesthetic agent in the atmosphere around the MGU-800/810 series may adversely affect the
measurement readings.
 SPIRO and ventilator cannot be used simultaneously.
 During the warming up process, the date of the last measurement accuracy check cannot be updated. Perform
the measurement accuracy check after the warming up process is completed.
 If the accuracy check is performed using a low pressure gas, the accuracy of gas measurement will be reduced.
Make sure to perform the accuracy check using the specified calibration gas before its expiration date.
 If the error persists, refer to Fukuda Denshi.
 About the MGU-810 Series

The adult flow sensor dead space is 6.9 mL and the flow resistance is 1.8 cmH
2
O at 60 L/min.
The pediatric flow sensor dead space is 0.75 mL and the flow resistance is 0.9 cmH
2
O at 10 L/min.
Adjust ventilation accordingly.

To prevent condensation, the patient breathing circuit, flow sensor and pressure tubing should not be directly
exposed to cooling equipment such as fans or cooling blankets.
 Leakage of gas from the patient breathing system may occur if the pressure or gas sampling lines are not
connected to the MGU-810.
CAUTION