manualshive.com logo in svg

Froling TX 150, Руководство по установке

Поделиться
Скачать
Froling TX 150 Скачать руководство пользователя страница 6

2.2 Qualification of assembly staff

CAUTION

Assembly and installation by untrained personnel:
Risk of personal injury and damage to property.

During assembly and installation:

❒ Observe the instructions and information in the manuals
❒ Only allow trained staff to carry out assembly and installation

 
Assembly, installation, initial startup and servicing must always be carried out by quali‐
fied personnel:
- Heating technician / building technician
- Electrical installation technician
- Froling customer services
The assembly staff must have read and understood the instructions in the documenta‐
tion.
 

2.3 Protective equipment for assembly staff

You must ensure that staff have the protective equipment specified by accident pre‐
vention regulations.

▪ For transportation, setup and assembly:

- suitable workwear
- protective gloves
- sturdy shoes

 

 

 

 

2

Safety

Qualification of assembly staff

6

Froling GesmbH | A-4710 Grieskirchen, Industriestraße 12 | www.froling.com

Содержание TX 150





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды