manualshive.com logo in svg

Froling TX 150, Руководство по установке

Поделиться
Скачать
Froling TX 150 Скачать руководство пользователя страница 18

4.5.2 Screwing the fire box with the heat exchanger

Positioning of the fire box from the side

❒ Insert the lift truck at the fire box opposite and lift it up as far as the fire box can be

positioned without colliding with the heat exchanger

❒ Bring in the fire box completely at the side of the heat exchanger and lower it slow‐

ly

❒ Remove the supporting post on the ash flange of the fire box

 

Positioning the fire box from the front
If there is not enough space to bring in the fire box from the side, it is possible to bring
it in from the front:

❒ Insert the lift truck at the fire box opposite the supporting post
❒ Place a piece of pipe, square timber or similar with a height of approx. 75 mm be‐

low the fire box as a distance piece

❒ Lift the fire box with the lifting truck and remove the supporting post on the ash

flange

❒ Position the loading arm of the lift truck by the openings of the main frame und in‐

sert the fire box as far as the distance piece can be positioned within the apron

❒ Lower the fire box, position the distance piece within the apron, lift the fire box

once again and bring it completely in.

 

 

4

Assembly

Mounting steps

18

Froling GesmbH | A-4710 Grieskirchen, Industriestraße 12 | www.froling.com

Содержание TX 150





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды