manualshive.com logo in svg

Froling TX 150, Руководство по установке

Поделиться
Скачать
Froling TX 150 Скачать руководство пользователя страница 22

4.5.6 Retrofitting the WOS bar (if necessary)

The WOS drive is always mounted on the back side of the boiler opposite to the con‐
trol box. Depending on delivery condition the WOS bar has to be adjusted accordingly:

❒ Loosen the clamping jaw at the actuating lever and remove them from the WOS

shaft

❒ Unscrew the bearing bush of the shaft

 

❒ Remove the blind plug on the opposite of the WOS shaft
❒ Loosen the screwing on the heat exchanger cover, set star grip to left-hand stop

and open the cover

 

 

❒ Remove safety pin of the WOS shaft and pull out the shaft
❒ Fit in the WOS shaft from the opposite and pull it through
❒ Remount the prior removed bearing bush and blind plug on the opposite side
❒ Remove the tension hook and remount it on the opposite as well

 

 

4

Assembly

Mounting steps

22

Froling GesmbH | A-4710 Grieskirchen, Industriestraße 12 | www.froling.com

Содержание TX 150





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды