Fluke 1586A Скачать руководство пользователя

Страница: 126 / 140

1586A

Users Manual

7-8

Table 7-1. Error Messages (cont.)

Error Code

Error Message

Causes and Solutions

Error 306

Not waiting for
reference

Cause:

CALibrate:NEXT command with a reference value

was received, but the reference value is not allowed for
current step.

Solution:

Check the parameter value and try again.

Error 307

Continue command
ignored

Cause:

CALibrate:NEXT command was received, but it is not

expected for current calibrate step.

Solution:

Check the parameter value and try again.

Error 318

Reading does not
match reference

Cause:

The measured value out of range, it might be caused

by wrong input signal or hardware defect.

Solution:

Make sure that the input signal matches the

requirement. If the input signal is correct, cycle the power. If
the error occurs again, contact Fluke (see Chapter 1).

Error 320

Timeout waiting for
reading

Cause:

Timeout while waiting readings from inguard.

Solution:

Cycle the power. If the error occurs again, contact

Fluke (see Chapter 1).

Error 322

Password missing

Cause:

CALibrate:ENABle command was received to unlock

the calibration but ADMIN password is not provided.

Solution:

Make sure that ADMIN password was sent with the

CALibrate:ENABle command.

Error 323

Wrong password

Cause:

CALibrate:ENABle command was received to unlock

the calibration but the ADMIN password is wrong.

Solution:

Make sure that correct ADMIN password was sent

with the CALibrate:ENABle command.

Error 324

Calibration locked

Cause:

The calibration is locked when a CALibrate command

was received.

Solution:

Use the CALibrate:ENABle command to unlock the

calibration first.

Error 325

Cannot get stable
readings

Solution 1:

Check calibrator and make sure that the correct

signal is being outputted from the calibrator.

Solution 2:

Cycle the power and run calibration again. If the

error occurs again, the relay card needs serviced, contact
Fluke (see Chapter 1).

Error 398

Anomalous error %d

Cause:

Unknown error occurred during the calibration

procedure.

Solution:

Restart the calibration procedure. If the error

occurs again, contact Fluke (see Chapter 1).

Содержание 1586A













































































































































Результаты поиска

Содержание 1586A

Отзывы:

Похожие инструкции для 1586A

Бренды по названию

Популярные бренды

Fluke 1586A, Руководство пользователя

Результаты поиска

Содержание 1586A

Отзывы:

Похожие инструкции для 1586A

Бренды по названию

Популярные бренды