Fluke 1586A Скачать руководство пользователя

Страница: 81 / 140

Input and Channel Configuration

Probe Library

3-35

Push



to input a new probe.

Select Label and push



to set a custom label or push



to read the label from

the channel.

Select Function and push



to change. Use the on-screen options to configure the

probe.

After the function and label is set, push



to save.

To edit a probe:

Push



Push





to highlight a channel then push



Push





to select Function then push



Push



to open the Probe Library.

Push





to highlight a probe in the list then push



to edit.

Select Label and push



to change the label.

Select Function and push



to change. Use the on-screen options to configure the

probe.

After the function and label is set, push



to save the changes.

Assign a probe to a channel:

Push



Push





to highlight a channel then push



Push





to select Function then push



Push



to open the Probe Library.

Push





to highlight a probe in the list then push



to assign it to the

channel shown.

Содержание 1586A













































































































































Результаты поиска

Содержание 1586A

Отзывы:

Похожие инструкции для 1586A

Бренды по названию

Популярные бренды

Fluke 1586A, Руководство пользователя

Результаты поиска

Содержание 1586A

Отзывы:

Похожие инструкции для 1586A

Бренды по названию

Популярные бренды