Fluke 1586A Скачать руководство пользователя

Страница: 127 / 140

Error Messages and Troubleshooting

Error Messages

7-9

Table 7-1. Error Messages (cont.)

Error Code

Error Message

Causes and Solutions

Error 399

Error at step %s

Cause:

An error occurred at present calibrating step.

Solution:

Check next error message for specific solution.

Error 400

External CJC not
configured

Cause:

A thermocouple channel is set to external CJC, but

the channel that is used to measure external CJC
temperature has not been configured.

Solution:

Configure the lowest module channel to PRT or

Thermistor with temperature reading, it will be used as
external CJC channel.

Error 401

Channel used as
external CJC

Cause:

Configure is changed to the channel that is used to

measure external CJC temperature.

Solution:

Turn off all thermocouple channels that are

configured for external CJC first.

Error 402

TC external reference
channel

Cause:

Configure the lowest module channel as TC with

external CJC.

Solution:

Check the parameter and make sure that the

lowest module channel is not configured as TC with an
external CJC.

Error 403

Parameter does not
meet present config

Cause:

Parameter or command is not allowed for present

configuration. For example: SENSe:NPLC 1 (@401) is
received, but channel 401 is DIO.

Solution:

Check the parameter value and try again.

Error 404

Channel limit
exceeded

Cause:

Too many channels in scan list (max. 178).

Solution:

Turn off some channels and try again.

Error 405

Channel used as
alarm trigger

Cause:

A channel cannot be set to OFF while it is used as

trigger channel for alarm test.

Solution:

Change the trigger channel setting or reconfigure

the trigger source.

Error 406

Alarm channel not
enabled

Cause:

The alarm channel selected to be the alarm trigger is

set to OFF.

Solution:

Enable and configure the alarm channel then try

again.

Содержание 1586A













































































































































Результаты поиска

Содержание 1586A

Отзывы:

Похожие инструкции для 1586A

Бренды по названию

Популярные бренды

Fluke 1586A, Руководство пользователя

Результаты поиска

Содержание 1586A

Отзывы:

Похожие инструкции для 1586A

Бренды по названию

Популярные бренды