Flexim FLUXUS G801 Скачать руководство пользователя страница 125

Страница: 125 / 177

15 Data transmission

FLUXUS G801

15.2 Terminal program

125

UMFLUXUS_G801V1-0EN, 2020-06-26

15.2.2

Offline transmission

• Start the terminal program.
• Enter the transmission parameters into the terminal program. The transmission parameters of the terminal program and

the transmitter have to be identical.

Selection of the interface for the offline transmission of data

• Select the menu item

serial transmis.

• Press ENTER until

Send Offline via

is displayed.

• Select the serial interface for the offline transmission of data.
This display will only be indicated if the transmitter has an interface RS485.

Transmitter settings

• Select the menu item

Print Meas.Val.

• Press ENTER.
The following message will be displayed if no measured values are stored.

• Press ENTER.
The following message will be displayed if the measured values are transmitted.

The progress of data transmission is displayed by a bar graph.

The following message will be displayed if an error has occurred during the serial transmission.

• Press ENTER.
• Check the connections and make sure the PC is ready to receive data.

Notice!

During the offline transmission only those data is transmitted that is stored in the transmitter.

Special Funct.\SYSTEM settings\serial transmis.

Special Funct.\SYSTEM settings\serial transmis.\Send Offline via

Special Funct.\Print Meas.Val.

NO VALUES

Print Meas.Val.

Send Header

.................

■■■■■■

.................

SERIAL ERROR

Print Meas.Val.

Содержание FLUXUS G801


















































































































































































Результаты поиска

Содержание FLUXUS G801

Отзывы:

Похожие инструкции для FLUXUS G801

Бренды по названию

Популярные бренды

Flexim FLUXUS G801, Руководство по эксплуатации

Результаты поиска

Содержание FLUXUS G801

Отзывы:

Похожие инструкции для FLUXUS G801

Бренды по названию

Популярные бренды