Flexim FLUXUS G801 Скачать руководство пользователя страница 97

Страница: 97 / 177

9 Measurement

FLUXUS G801

9.3 Start of the measurement

UMFLUXUS_G801V1-0EN, 2020-06-26

Input of the sound path number

A value for the number of sound paths corresponding to the connected transducers and the entered parameters is

recommended.
• Change the value, if necessary.
• Press ENTER.

Profile correction

With disturbance

is selected in the menu item

Special Funct.\SYSTEM settings\Measuring\

ProfileCorr 2.0

, it has to be checked whether the measurement arrangement is appropriate.

If the number of sound paths is odd and more than one measuring channel is activated, the following display appears:

• Select

if there are 2 transducer pairs in X arrangement or displaced X arrangement at the measuring point

(appropriate measurement arrangement). The profile correction 2.0 at non ideal inflow conditions will be used.

Transverse flow effects will be compensated.

• Select

yes

if there is only one transducer pair at the measuring point (inappropriate measurement arrangement). The

profile correction 2.0 at non ideal inflow conditions cannot be used. The profile correction 2.0 at ideal inflow conditions

will be used. Transverse flow effects will not be compensated.

• Press ENTER.
If

yes

is selected, the following menu messages are displayed:

Adjustment of the transducer distance

The recommended transducer distance will be displayed.
• Mount the transducers on the pipe adjusting the transducer distance.
• Press ENTER.

measuring channel

Reflec –

reflection arrangement

Diagon –

diagonal arrangement

The transducer distance is measured between the inner edges of the transducers.
In case of a measurement in diagonal arrangement on very small pipes, a negative transducer distance is possible.

The diagnostics window is displayed.

Measuring\Channel\...\Sound Path

Measuring\...\Transd. Distance

Notice!

The accuracy of the recommended transducer distance depends on the accuracy of the entered pipe and fluid

parameters.

A: Alone at measp

>NO<

yes

Disturb correct.

not applicable!

I assume ideal

inlet conditions

Содержание FLUXUS G801


















































































































































































Результаты поиска

Содержание FLUXUS G801

Отзывы:

Похожие инструкции для FLUXUS G801

Бренды по названию

Популярные бренды

Flexim FLUXUS G801, Руководство по эксплуатации

Результаты поиска

Содержание FLUXUS G801

Отзывы:

Похожие инструкции для FLUXUS G801

Бренды по названию

Популярные бренды