manualshive.com logo in svg

Flexim FLUXUS G801, Руководство по эксплуатации

Поделиться
Скачать
Flexim FLUXUS G801 Скачать руководство пользователя страница 133

16  Advanced functions

FLUXUS G801

 16.6  FastFood mode

133

UMFLUXUS_G801V1-0EN, 2020-06-26

During the measurement, the designation of the physical quantity is displayed in capital letters to indicate that the value is 

uncorrected.

• Press ENTER.

If 

yes

 is selected, the uncorrected flow velocity will only be used if the flow velocity is selected as physical quantity in the 

program branch 

Output Options

.

All other physical quantities (volumetric flow rate, mass flow rate, etc.) will be determined with the corrected flow velocity.
During the measurement, the designation of the physical quantity "flow velocity" is displayed in capital letters to indicate 

that the value is uncorrected.
• Press ENTER.
In both cases, the corrected flow velocity can also be displayed.

Press 

 to scroll until the flow velocity is displayed. The uncorrected flow velocity is marked with 

U

.

Uncorrected flow velocities transmitted to a PC are marked with 

uncorr.

16.6

FastFood mode

The FastFood mode allows to measure high dynamic flows. A continuous adaptation to changing measuring conditions is 

only partially realized in the FastFood mode.
• The sound speed of the fluid is not updated. The last measured value of the sound speed before toggling to the 

FastFood mode is used.

• It is not possible to change the measuring channel. The measurement takes place on one channel only. As long as the 

FastFood mode is activated, no measurement is carried out on the other channels.

• The outputs of the FastFood mode activated channel can still be used. They are updated every 100 ms independently 

from the storage rate.

• Outputs for further channels (multi-channel measurement) transmit an error value.
• The measured values are stored with the storage rate of the FastFood mode.
• The FastFood mode has to be enabled and activated.

16.6.1

Enabling/disabling the FastFood mode

• Enter the HotCode 

007022

.

• Select 

yes

 to enable the FastFood mode, or 

no

 to disable it.

• Press ENTER.

If the FastFood mode is enabled, a time t has to be entered. When the FastFood mode is started, the signal amplification 

settings will always be checked after the expiration of time t.
Enter zero if no check is to be carried out.

Enable FastFood

Enable FastFood\FF-check (0=OFF)

A:FLOW VELOCITY

2.60

m/s

A:PROFILE CORR.

>no<

YES

A:Flow Velocity

*U

24

m/s

Содержание FLUXUS G801


















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды