Flexiheat Compact ePlus12 Скачать руководство пользователя страница 43

Страница: 43 / 48

Cleaning and maintenance

8.3

Discharge air from the installation
and fill it with water

WARNING:

Material damages caused by heat

straining. Filling the heating installation in a warm
state can cause cracks due to tension.



Fill the heating installation in cold state
only (temperature of the starting line
maximum 40

°C).

WARNING:

Material damages caused by

frequent

filling!

Due to frequent filling of heating installation with
water, it can be damaged by corrosion or by
formation of limescale, depending on the
properties of water.



Inspect the heating installation for

impermeability, and the expansion
container for functionality.

Connect the hose to the water tap.

Fill the hose with water and attach to the hose

connector of the tap for charging and discharging.

Fasten the hose with the clout of the hose and

open the charging and discharging tap.

Fill the heating installation slowly and monitor the

overview of pressure (manometer).

Discharge the air during the filling process.

Close the discharging tap when the operating pressure is reached.

Water must be refilled when the operating pressure

drops due to discharging of air.

Remove the hose from the charging and discharging tap.



Содержание Compact ePlus12

















































Результаты поиска

Содержание Compact ePlus12

Отзывы:

Похожие инструкции для Compact ePlus12

Бренды по названию

Популярные бренды

Flexiheat Compact ePlus12, Инструкции по установке, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Compact ePlus12

Отзывы:

Похожие инструкции для Compact ePlus12

Бренды по названию

Популярные бренды