Flexiheat Compact ePlus12 Скачать руководство пользователя страница 41

Страница: 41 / 48

CODES

WARNING codes

- Warning: approaching the lower limit of the allowed pressure (0.8 bar)

SHOULD BE DONE - Fill the system with water to the necessary pressure

- Warning: approaching the upper limit of the allowed pressure (2.2 bara)

SHOULD BE DONE - Bring the system to the required pressure

- Warning: approaching the lower limit of the allowed temperature (5 degrees) of the HEATING SYSTEM

SHOULD BE DONE - Switch on room thermostat and heaters or activate freezing protection regime

- Warning: approaching the upper limit of the allowed temperature (80 degrees) of the HEATING SYSTEM

SHOULD BE DONE - Lower the power of the boiler, check whether the valves are open

ERROR codes

- Error: the set parameters are not within limits (this is practically impossible

unless the eeprom is empty and the device is switched on for the first time) - all switched off

- Error: reached lower limit of the allowed pressure (0.3 bar)

– all switched off

REMEDY

– Fill the system with water to the necessary pressure, check the sealing of all connections

- Error: reached upper limit of the allowed pressure (2.6 bar) - all switched off

REMEDY - Bring the system to the required pressure by discharging air and water when needed

- Error: reached lower limit of the allowed temperature (3

˚C) - all switched off

- Error: reached upper limit of the allowed temperature (85

˚C) – the pump is switched on continuously

REMEDY - Switch off the main fuses for powering the boiler with electricity, call the service center

- Error: reached lower limit of the allowed temperature of the BOILER (3

˚C) - INFORMATIVE

- Error: sensor of temperature of the boiler in break or short circuit - all switched off

REMEDY - Switch off the main fuses for powering the boiler with electricity, call the service center

- Error: sensor of temperature of the boiler in break or short circuit

– no sanitary water preparation

REMEDY - call the service center

- Error: sensor of pressure in break or short circuit

– all switched off

REMEDY - Switch off the main fuses for powering the boiler with electricity, call the service center

Graphical overview of operation of the device
based on pressure and temperature

Содержание Compact ePlus12

















































Результаты поиска

Содержание Compact ePlus12

Отзывы:

Похожие инструкции для Compact ePlus12

Бренды по названию

Популярные бренды

Flexiheat Compact ePlus12, Инструкции по установке, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Compact ePlus12

Отзывы:

Похожие инструкции для Compact ePlus12

Бренды по названию

Популярные бренды