background image

TST

 

Assembly instructions

 

FUZ2 -A/-B/-C/-CX/-L 

 

FEIG ELECTRONIC GmbH

 

Page 47 of 71

 

FUZ2-A-B-C-CX-L_Montageanleitung_GB

_10.docx

 

9.4  Renewed request for "learning" limit positions 

If the limit positions have been pre-taught when using electronic limit switches, but these are not suitable for 
the respective door, the learning process for limit positions can be requested again 
 
The following parameter must be set for this: 
 

  P.210 = 5 Renewed teaching of all limit positions 

9.5  Boost / increase in performance forlow speeds 

Boost is used to increase the power of the drives at low speed. Too much or too little boost can result in 
improper door operation. The boost adjustment range is 0-30%. Too much boost will result in an over current 
fault (F.510/F.410). In this case the boost must be reduced. 
If the boost is low or 0 and the motor still does not have sufficient force to move the door, the boost must be 
increased. 
Due to the large number of door types, the correct setting for boost must be determined empirically. 

1.  Open parametrization mode by pressing the 

STOP and 

OPEN keys simultaneously. 

2.  Open Boost parameter by pressing the

 arrow keys. Boost can be set separately for OPEN and 

CLOSE.  
 

  Boost for opening: P.140 

  Boost for closing: P.145 

 

3.  Open the parameter by momentarily pressing 

 STOP and use the  

 arrow keys to change it in 

small steps of max. 5, then save by pressing 

 STOP (longer). 

4.  After changing the boost, exit parametrization mode by pressing the 

 STOP button for a long time 

and test the setting in run mode. 

 

    

You can use diagnostic parameter P.910 = 2 to display the actual motor current. The boost should be 

set so that the motor current remains as low as possible.

 

Содержание TST FUZ2-A








































































Отзывы: