Feig Electronic TST FUZ2-A Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 71

background image

TST

Assembly instructions

FUZ2 -A/-B/-C/-CX/-L

FEIG ELECTRONIC GmbH

Page 59 of 71

FUZ2-A-B-C-CX-L_Montageanleitung_GB

_10.docx

No.

Description

Possible reason for error

F.851

Max. Number of allowed
Reversings, because of bad
WiCAB radio, exceeded.

The radio connection interrupts during door drive for a short time

F.852

Communication error between TST
FSx and controller

This error occurs when the controller looses RS485 communication for min. 1 second with the stationary unit of
the radio strip TST FSx. Possible causes are:
• The stationary unit is broken
• The stationary unit is not or wrong connected

F.853

TST PE_FSBS operating voltage
too low

The operating voltage of encoder TST PE_FSBS is too low (less than 8V) As a result, the calculation of the
position must be terminated.

F.856

Communication error between
mobile and stationary unit

This error occurs if the mobile unit and the stationary unit of the radio control unit could not establish radio
communication for at least
1 second. Possible causes are:
• No mobile unit in radio range
• The battery of the mobile unit is empty or not connected
• The antenna of the stationary unit is not connected or missing
• Moile unit or stationary unit is defective

F.857

Battery empty

• The battery voltage is under the limit set with Parameter P.F0B
• The battery voltage of the mobile unit is to low
• Use new battery and set back battery capacity to 100% by pressing the stop key for long time in P.F09.
• To deactivate this error message you can set P.F09 and P.F0B to 0

F.859

Software version

The software versions of the stationary and the mobile unit are not compatible. No safe trip possible.

F.860

Internal fault stationary unit

Internal system fault on the stationary unit.

F.861

Internal fault mobile unit

Internal system fault on the mobile unit.

F.862

Internal positioning system error

Internal error of the positioning system. Presumably, the magnet is not attached properly.

F.867

Address of mobile unit not set

• The address of the mobile unit was not set so far
• The address has to be set in Parameter P.F07
• The address is written on a sticker on the mobile unit

F.910

No communication to expansion
board possible

• The communication to the expansion board is not possible
• No expansion board plugged in
• CAN Connection interrupted (Broken cable or no supply voltage for extension board)

F.911

ROM error on extension board

• Wrong Flash-Code
• Defective hardware or noise-saturated environment

F.912

RAM error on extension board

• Defective hardware or noise-saturated environment

F.920

Internal 2.5 V reference voltage
incorrect

• Hardware defect

«
...
59
60
61
62
63
...
»

Содержание TST FUZ2-A








































































Отзывы:

Нет отзывов

Похожие инструкции для TST FUZ2-A

Бренд: XBOX Страницы: 4

Бренд: Aalborg Страницы: 15

Бренд: Aalborg Страницы: 48

Бренд: Watts Страницы: 8

U1000 iQpump Drive

Бренд: YASKAWA Страницы: 426

Бренд: YASKAWA Страницы: 26

Бренд: YASKAWA Страницы: 210

Z1000 CIMR-ZU*A Series

Бренд: YASKAWA Страницы: 400

Z1000 CIMR-ZU*A Series

Бренд: YASKAWA Страницы: 466

Бренд: Eaton Страницы: 10

Бренд: Idemia Страницы: 29

Easywave ST01 Series

Бренд: Eldat Страницы: 2

WFHC 06Z 02 HC RF 24

Бренд: Watts Страницы: 18

Бренд: Waters Страницы: 39

DHI-IPMECD-3021 Series

Бренд: Dahua Technology Страницы: 28

Errata MSP430F6779

Бренд: Texas Instruments Страницы: 27

Бренд: FOR-A Страницы: 6

Бренд: turck Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды