Feig Electronic TST FUZ2-A Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 71

background image

TST

Assembly instructions

FUZ2 -A/-B/-C/-CX/-L

FEIG ELECTRONIC GmbH

Page 57 of 71

FUZ2-A-B-C-CX-L_Montageanleitung_GB

_10.docx

No.

Description

Possible reason for error

F.752

Loss of communication with
encoder

• Interface cable defective / interrupted
• Channel A and B connected over cross
• Absolute encoder processor electronics defective
• Defective hardware or electrically noisy environment
• Use a shielded control cable
• Install a RC element (100Ω+100nF) at the brake

F.760

Position outside of window

• Position encoder drive defective
• Absolute encoder processing electronics defective
• Defective hardware or electrically noisy environment

F.763

DES-B Error

• Position encoder drive defective -> make a reset

F.766

Internal error TST PD/PE

• The position encoder TST PD / PE is disturbed -> make a reset

F.767

Overtemperature TST PD

• The temperature in the encoder housing is to high

F.768

Battery voltage

• The voltage of the buffer battery is to low → change battery

F.769

Rotation speed of PD shaft to high

• The rotation speed of the shaft where the encoder is mounted is to high → mount the encoder on another shaft

F.770

Door way is to high for the
parameter set Encoder resolution

• The Value of the Parameter P.202 (set Encoder resolution) is to high for the combination encoder and door.

F.801

Wrong Test of input 1 of the mobile
unit TST FSx

• Input 1 of the mobile unit was tested wrong
• The device which is connected to the input does not work correctly
• The mobile unit is defective

F.802

Wrong Test of input 2 of the mobile
unit TST FSx

• Input 2 of the mobile unit was tested wrong
• The device which is connected to the input does not work correctly
• The mobile unit is defective

F.803

Wrong Test of input 3 of the mobile
unit TST FSx

• Input 3 of the mobile unit was tested wrong
• The device which is connected to the input does not work correctly
• The mobile unit is defective

F.804

Wrong Test of input 4 of the mobile
unit TST FSx

• Input 4 of the mobile unit was tested wrong
• The device which is connected to the input does not work correctly
• The mobile unit is defective

F.80A

Wrong Test of input A of the
stationary unit TST FSx

• Input A of the stationary unit was tested wrong
• The device which is connected to the input does not work correct
• The stationary unit is defective

«
...
57
58
59
60
61
...
»

Содержание TST FUZ2-A








































































Отзывы:

Нет отзывов

Похожие инструкции для TST FUZ2-A

Бренд: Warner Electric Страницы: 3

Бренд: iCeeO2 Страницы: 7

Бренд: SABAF Страницы: 6

Бренд: Samson Страницы: 78

Бренд: Rachio Страницы: 16

Бренд: Canon Страницы: 2

Бренд: Panasonic Страницы: 72

Бренд: Panasonic Страницы: 45

Бренд: Panasonic Страницы: 24

Бренд: ZirbenLüfter Страницы: 36

Бренд: Jetline Страницы: 58

EP Series Pro-Bloc

Бренд: Parker Страницы: 11

Бренд: Parker Страницы: 22

Бренд: Parker Страницы: 2

Simply Smart PY75 A Series

Бренд: BABYTREND Страницы: 32

Бренд: TeleMann Страницы: 4

CIATControl OPC Server

Бренд: CIAT Страницы: 32

Бренд: Danfoss Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды