Feig Electronic TST FUZ2-A Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 71

background image

TST

Assembly instruction

FUZ2 -A/-B/-C/-CX/-L

FEIG ELECTRONIC GmbH

Page 10 of 71

FUZ2-A-B-C-CX-L_Montageanleitung_GB_10.docx

4.2 Additional heat sink for small housing

If the controller is installed in an additional housing so that the cold air supplied to the heat sink is not
sufficient, for example, in barrier housings, an additional heat sink must be inserted between the controllers
housing and the additional housing to dissipate heat to the outside. This additional heat sink is mounted, for
example, on the barrier housing and the controller is mounted above it without the spacers, so that the
additional heat sink is clamped between the controller and the cabinet.

The additional heat sink must have the following design:

Figure 4: Additional heat sink

«
...
10
11
12
13
14
...
»

Содержание TST FUZ2-A








































































Отзывы:

Нет отзывов

Похожие инструкции для TST FUZ2-A

Бренд: ABB Страницы: 2

Бренд: Faber Страницы: 8

Бренд: Gardena Страницы: 16

Бренд: MADRIX Страницы: 28

Бренд: Data I/O Страницы: 88

Бренд: Data Aire Страницы: 13

Бренд: Faulhaber Страницы: 66

Бренд: Hama Страницы: 12

Бренд: Hama Страницы: 12

Бренд: Hama Страницы: 14

Бренд: Hama Страницы: 8

Бренд: NAPCO Страницы: 48

Magnum Alert 2600

Бренд: NAPCO Страницы: 68

Бренд: Unitech Страницы: 55

Бренд: S&C Страницы: 8

Бренд: Paradox Страницы: 32

Бренд: Zamel Страницы: 23

Бренд: Zamel Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды