Feig Electronic ID ISC.LRU3000 Скачать руководство пользователя страница 43

Страница: 43 / 193

OBID

i-scan

UHF

Manual

ID ISC.LRU3000/3500

FEIG ELECTRONIC GmbH

Page 43 of 193

H90202-7e-ID-B.docx

FREQ_US:

Defines the Reader specific frequency channel usage .

Byte

Bit

Function

upper channel

lower channel

upper/lower channel:

(AirInterface.Region.UHF.FCC.Channel.UpperChannel)

(AirInterface.Region.UHF.FCC.Channel.LowerChannel)

Frequency which is used by the FCC Reader as upper and lower limit.

NOTE:

These settings are only applicable if Region [0xFF] Unknown is selected.

These settings are only applicable for FCC Readers.

NR_PREFERRED_CHN: (AirInterface.Region.UHF.EU.Channel.EN302208_4_ChannelPlan.

PreferredChannels.NoOfChannels)

Number of channels (1- 4) used by the European Reader.

NOTE:

These settings are only applicable if Region [0xFF] Unknown is selected.

These settings are only applicable for EU Readers

upper/lower

channel

Frequency

902,75 MHz

903,25 MHz

903,75 MHz

...

927,25 MHz

Содержание ID ISC.LRU3000


































































































































































































Результаты поиска

Содержание ID ISC.LRU3000

Отзывы:

Похожие инструкции для ID ISC.LRU3000

Бренды по названию

Популярные бренды

Feig Electronic ID ISC.LRU3000, Руководство пользователя

Результаты поиска

Содержание ID ISC.LRU3000

Отзывы:

Похожие инструкции для ID ISC.LRU3000

Бренды по названию

Популярные бренды