Feig Electronic ID ISC.LRU3000 Скачать руководство пользователя страница 25

Страница: 25 / 193

OBID

i-scan

UHF

Manual

ID ISC.LRU3000/3500

FEIG ELECTRONIC GmbH

Page 25 of 193

H90202-7e-ID-B.docx

NOTE:

A READER-ID = 0x00000000 disables the password function.

If the Reader ID is not set 0x00000000 the configuration page CFG0 is automatically read
protected.

A read with the command

8.3. [0x8A] Read Configuration

will always get ‘0x00000000’.

To change the READER-ID you must write to the CFG0 immediately after the Login to the
Reader with the command

9.11. [0xA0] Reader-Login

A changed password becomes valid after a System Reset

9.3. [0x64] System Reset.

The commands

8.4. [0x8B] Write Configuration

and 8.5. [0x8C] Reset Configuration don’t

change the CFG0 register if all configuration blocks are used. Also access protected Confi-
guration Pages will not be influenced by these Commands.

The command

9.11. [0xA0] Reader-Login

is used to enable configuration data access.

It is possible to disable the READER-ID with an activation code, if the READER-ID is un-
known. The activation code must be ordered by your supplier or FEIG ELECTRONIC GmbH.

Config Protection

By means of Config Protection, the access to the configuration parameters stored within the Read-
er

is protected by a 32-bit password, the "READER-ID". This means that only after a "Login" with a

valid READER-ID the configuration parameters in the EEPROM of the Reader can be read and
changed in the EEPROM of the Reader.

Содержание ID ISC.LRU3000


































































































































































































Результаты поиска

Содержание ID ISC.LRU3000

Отзывы:

Похожие инструкции для ID ISC.LRU3000

Бренды по названию

Популярные бренды

Feig Electronic ID ISC.LRU3000, Руководство пользователя

Результаты поиска

Содержание ID ISC.LRU3000

Отзывы:

Похожие инструкции для ID ISC.LRU3000

Бренды по названию

Популярные бренды