manualshive.com logo in svg

Feig Electronic ID ISC.LRU3000, Руководство пользователя

Поделиться
Скачать
Feig Electronic ID ISC.LRU3000 Скачать руководство пользователя страница 189

OBID

 

i-scan

 ® 

UHF 

Manual 

ID ISC.LRU3000/3500 

 

FEIG ELECTRONIC GmbH 

Page 189 of 193 

H90202-7e-ID-B.docx 

 

Hex-value 

Transponder Status 

0X08 

Authent Error  

•

 

If access password is wrong 

 

 

Hex-value 

Parameter Status 

0x10 

EEPROM-Failure: 

The EEPROM of the Reader is not able to be written on. 

Before writing onto the EEPROM a faulty checksum of parameters has been detected. 

0x11 

Parameter-Range-Error: 

The value range of the parameters was exceeded. 

0x13 

Login-Request: 

Configuration access without having logged in to the Reader before. 

0x14 

Login-Error: 

Login attempt with wrong password. 

0x15 

Read Protect: 

The configuration block is reserved for future use. 

0x16 

Write Protect: 

The configuration block is reserved for future use. 

0x17 

Firmware activation required:  

The firmware must be activated first using ISOStart demo program and the command “Set Firmware 
Upgrade”. The update code must be ordered by Feig Electronic.  
1. Read the Device-ID using the command [0x66] Firmware version (Mode 0x80) 
2. Send the Device-ID and the serial number of the reader to Feig Electronic 
3. Write the upgrade code into the reader using the command [0x5F] Set Firmware Update

 

0x18 

Wrong Firmware:  

•

 

Firmwareversion conflict between RFC and FPGA 

•

 

Conflict between the supported tagdrivers of RFC and FPGA 

•

 

Readertype is not supported by the FPGA 

•

 

Mismatch between RFC Firmware and Hardware 

 

 

Hex-value 

Interface Status 

0x80 

Unknown Command: 

The Reader does not support the selected function. 

0x81 

Length-Error: 

The selected function has the wrong number of parameters. 

0x82 

Command not available: 

A Host command was sent to the Reader in the Buffered Read Mode. 

A Buffered Read Mode protocol was sent to the Reader in the standard mode 

The command with More bit does not correspond with the last command 

Содержание ID ISC.LRU3000


































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды