FBII XL-1S, Инструкции по подключению и установке

Страница: 21 / 71

4–1
S E C T I O N 4
Keypad Mounting
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
XK-104 Keypad
The XK-104 Keypad may be surface mounted in the following ways:
A. Directly to a control panel having a keypad cutout on the front of its enclosure.
B. Directly to a single or double gang electrical junction box.
C. Directly to a wall or other surface.
1. Remove the keypad cover assembly from the rear mounting
plate. Insert a small screwdriver blade in the COVER PRY-OFF
SLOTS at the lower edge of the keypad (see Diagram 2) and
twist to pry off the cover assembly.
2. Mount the rear plate (see Diagram 3).
NOTE: The plate is correctly oriented when its part number,
molded into the plastic, is upright.
A. Mounting Directly To Control Panel Enclosure:
If the control panel has a keypad cutout on the front face of its
enclosure, remove the cutout and mount the plate to the
enclosure's face via HOLES "A" (see diagram 3) and the four
screws and nuts provided.
NOTE: The VT-200 attack-proof enclosure does not contain a
keypad cutout.
B. Mounting Directly To An Electrical Junction Box:
The plate can be mounted directly to a single or double gang
electrical junction box. Use the screw holes provided and
HOLES "B" for a single gang box or HOLES "A" for a double
gang box.
C. Mounting Directly To A Wall Or Other Surface:
Provide a wiring hole in the mounting surface. Position the
plate's WIRING OPENING over the hole and mounting plate,
using HOLES "A" and/or "B" in conjunction with appropriate
mounting hardware (not provided) for the type of surface.
3. Complete the keypad wiring as required for the control with
which the keypad is to be used.
4. Replace the keypad cover assembly on the rear plate. Starting
at the upper edge of the plate, engage the plate's two HOLDING
HOOKS (see diagram 3) into the recesses provided for them
inside the upper edge of the cover assembly and snap the lower
edge of the cover assembly and snap the lower edge of the cover
onto the two SNAP HOOKS at the lower edge of the plate.
NOTE: (Optional) If desired, cover and plate can be further
secured together by inserting a screw (provided) into the SLOT
at the keypad's lower edge.
NOTE: When surface mounting the keypad, and using screws with heads larger than the screws provided
with the unit, place electrical tape over the screws to prevent them from interfering with the keypad
operation. In the future the back plate of the keypad will provide additional countersinking for screws with
larger heads.
Diagram 2: BOTTOM VIEW OF KEYPAD
COVER
REAR PLATE
BREAK-AWAY RIBS (4)
(FOR EXPOSED WIRING ENTRY.)
SLOT FOR COVER SECURING SCREW
(OPTIONAL)
COVER PRY-OFF SLOTS (2)
(TO REMOVE COVER, INSERT SMALL
SCREWDRIVER BLADE AND TWIST.)
DOOR
Diagram 3: REAR MOUNTING PLATE
A A B
A
A B
N6054
HOLDING HOOKS (2)
(FOR HOLDING COVERS UPPER EDGE)
HOLES “A” (4)
(FOR MOUNTING TO
CONTROL PANEL’S
ENCLOSURE OR
TWO GANG
ELECTRICAL BOX)
HOLES “B” (2)
(FOR MOUNTING TO
SINGLE GANG
ELECTRICAL BOX)
HOLES “A” OR “B”
(CAN BE USED
FOR WALL MOUNTING)
SNAP HOOKS (2)
(FOR HOLDING COVER’S
LOWER EDGE)
BREAK-AWAY RIBS (4)
(FOR EXPOSED WIRING ENTRY.)
POST FOR COVER
SECURING SCREW
(OPTIONAL)
WIRING
OPENING
(FOR
CONCEALED
WIRING)