Essilor Instruments DELTA Скачать руководство пользователя страница 82

Страница: 82 / 187

2. C

ONFIGURING

DRILLING

POINT

This section describes the procedures for the creation and positioning of a drilling point:

•

Creating a drilling point

(

p.85)

•

Delete one drilling point

(

p.86)

•

Dimensioning a drilling point

(

p.86)

•

Adjusting the position of a drilling point

(

p.87)

The positions of the various drilling points must be set before the centering of the lens.

Both lenses are set simultaneously.

a. Creating a drilling point

Press

to create a new drilling point.

Select the type of drilling (drill-hole, slot or notch).

Press on the shape at the spot where you want to position the drilling point.

The drilling point created is displayed in red in the shape:

The drilling coordinates are displayed on the right of the work screen;

Press

to copy the drilling points from the nasal area to the temporal area and vice-versa.

On the tracer-centerer-blocker, you can configure up to 6 drilling points per side (nasal and temporal) of a

shape.

SER

ANUAL

> VI. P

REPARING

DRILLED

JOB

Delta - Edging System > V1- 02-2020

Содержание DELTA




























































































































































































Результаты поиска

Содержание DELTA

Отзывы:

Essilor Instruments DELTA, Руководство пользователя, Страница: 82 / 187

Результаты поиска

Содержание DELTA

Отзывы: