Essilor Instruments DELTA Скачать руководство пользователя страница 80

Страница: 80 / 187

The following screen is displayed:

Work area

Colors which may appear on screen:

◦

(green) Current shape (from the traced shape) and associated drilling points

◦

(cyan) Current shape (obtained by symmetry with the traced shape) and associated drilling

points

◦

(yellow) Limit of the no-drill area

◦

(orange) Nasal or temporal side indicator

◦

(red) Selected drilling point

◦

(blue) Reference drilling point (by default, the first one created on each side – nasal and

temporal)

◦

A drilling point with a color infill indicates non through-drilling

Curve angle

Binocular view

Active eye

The selected eye has an orange frame around it.

Type of drilling

◦

Drill-hole

◦

Slot

◦

Notch

SER

ANUAL

> VI. P

REPARING

DRILLED

JOB

Delta - Edging System > V1- 02-2020

Содержание DELTA




























































































































































































Результаты поиска

Содержание DELTA

Отзывы:

Essilor Instruments DELTA, Руководство пользователя, Страница: 80 / 187

Результаты поиска

Содержание DELTA

Отзывы: