Essilor Instruments DELTA Скачать руководство пользователя страница 105

Страница: 105 / 187

In certain cases, the lens base or thickness makes grooving impossible.

> An error message is displayed.

> The white central line becomes red on the entire contour of the lens.

a. Automatic grooving

Call up the desired shape located on the tracer.

The shape is displayed on the edger work screen.

After tracing a pattern, demo lens or re-cut lens, without any drilling settings:

•

the groove finish is selected by default.

•

The automatic mode is selected by default.

If you wish to make a groove of which the depth and the width are lower than 0.60 mm:

Directly define the groove in the screen.

Press

and

to regulate the depth and the width of the groove

Depth (mm)

Width (mm)

By default

0.60

Minimum

0.20

0.60

Maximum

1.20

Select lens material.

Select the type of cycle.

Choose whether or not to polish and/or chamfer your lens.

For more information, consult the section Edging a lens > Perform a polishing

(

p.121)

and Edging

a lens > Perform a chamfering

(

p.121)

Close the door.

Delta - Edging System > V1- 02-2020

108

SER

ANUAL

> VII. E

DGING

LENS

Содержание DELTA




























































































































































































Результаты поиска

Содержание DELTA

Отзывы:

Essilor Instruments DELTA, Руководство пользователя, Страница: 105 / 187

Результаты поиска

Содержание DELTA

Отзывы: