Essilor Instruments DELTA Скачать руководство пользователя страница 29

Страница: 29 / 187

Enter the D-dimension value, then press

to confirm.

Take care systematically to measure the D-dimension of your frame to confirm the value entered

by the manufacturer on the arms of the frame.

Tracing - tracing mode

In tracing - tracing mode, the result of the tracing is displayed in the work area of the tracing screen.

For more information on work modes, refer to the section Tracing > Tracing environment > Jobs and

work modes

(

p.22)

Before Centering

Once tracing has been carried out, you can:

•

Enter the wrap angle and the frame base for optimal centering precision.

•

Add drilling points to the shape. For more information, refer to the section Preparing a drilled job

(

p.82)

4. E

NTER

THE

CURVE

AND

FRAME

BASE

During monocular tracing, the curve angle and the frame base cannot be measured. To optimize centering

precision, it is recommended to enter these values after tracing a pattern, a recut lens or a demo lens.

Prerequisite: before entering the curve angle and the frame base, it’s necessary to perform the optical

tracing of the pattern, a demo lens or a recut lens

(

p.28)

SER

ANUAL

> III. C

ARRY

OUT

OPTICAL

TRACING

Delta - Edging System > V1- 02-2020

Содержание DELTA




























































































































































































Результаты поиска

Содержание DELTA

Отзывы:

Essilor Instruments DELTA, Руководство пользователя, Страница: 29 / 187

Результаты поиска

Содержание DELTA

Отзывы: