Essilor Instruments DELTA Скачать руководство пользователя страница 111

Страница: 111 / 187

Using the cursor, select the point on the curve that you want to move or click directly on the screen.

Use the buttons

and

to move the point on the selected curve.

•

Press

to move it towards the front surface of the lens.

•

Press

to move it towards the rear surface of the lens.

The curve cannot be moved more than the minimum distance between the front and rear surfaces

observed on the groove before the modification.

The position of the groove as well as the distances between the center of the groove and the front &

rear surfaces of the lens are displayed in the zoom window.

Close the door.

Press

to go back to the customized bevel finish screen.

For the second lens, the customized groove icon is pre-selected and the trajectory modification icon

is displayed.

f. Displacement of the groove curve

The displacement of the groove curve enables you to move the groove without modifying its curve or

perimeter.

Press

from the customized groove finish screen.

You will access the trajectory modification screen.

Press

to select the displacement of the curve.

Use the

and

buttons to displace the curve.

Delta - Edging System > V1- 02-2020

114

SER

ANUAL

> VII. E

DGING

LENS

Содержание DELTA




























































































































































































Результаты поиска

Содержание DELTA

Отзывы:

Essilor Instruments DELTA, Руководство пользователя, Страница: 111 / 187

Результаты поиска

Содержание DELTA

Отзывы: