Essilor Instruments DELTA Скачать руководство пользователя страница 46

Страница: 46 / 187

Enter the half PD and pupillary height.

The target moves.

Lower the tube.

Insert the posiblock and its pad in the centering device.

Raise the tube back into centering position.

Position the lens on the tube, with the convex side on the tube.

In three focimeter dots mode:

move the lens slowly until the three focimeter dots are perfectly

aligned on the target.

•

Place the central point in the square

•

Place the two external points between the two dotted lines, as close as possible to the central line

In micro-engraving mode:

move the lens slowly until the micro-engravings are perfectly aligned on

the target.

The lens is centered and ready to be blocked.

HREE

FOCIMETER

DOTS

ICRO

ENGRAVINGS

To block the lens, refer to the section Centering a lens > Blocking a lens

(

p.62)

Delta - Edging System > V1- 02-2020

SER

ANUAL

> IV. C

ENTER

AND

BLOCK

LENS

Содержание DELTA




























































































































































































Результаты поиска

Содержание DELTA

Отзывы:

Essilor Instruments DELTA, Руководство пользователя, Страница: 46 / 187

Результаты поиска

Содержание DELTA

Отзывы: