Essilor Instruments DELTA Скачать руководство пользователя страница 168

Страница: 168 / 187

10. M

AINTAIN

AND

CLEAN

THE

TRACER

CENTERER

BLOCKER

This section describes the tracer-centerer-blocker maintenance and cleaning procedures:

•

Precautions required

(

p.171)

•

Clean the reflectors and the lens

(

p.171)

•

Clean the tube

(

p.171)

a. Precautions required

To avoid any incidents, unplug the device before all cleaning operation.

•

Clean the tracer-centerer-blocker cover regularly: use neutral detergent (e.g. dish product) diluted
with water on a soft cloth.

•

Never clean the apparatus with chemical products (e.g.: petrols, thinners, solvents).

b. Clean the reflectors and the lens

Dirty or striped reflectors or a lens can cause tracing defects. Be careful and clean them using a soft and dry

rag regularly.

Never pour liquid on these parts.

c. Clean the tube

In order not to damage the LED band surrounding the centering chamber, clean the tube using a dry rag

without rubbing it.

Never pour liquid on these parts.

11. M

AINTAINING

AND

CLEANING

THE

EDGER

This section describes the procedures for servicing and cleaning the digital system:

•

Precautions required

(

p.172)

•

Clean the GCD module

(

p.172)

•

Clean the door

(

p.172)

•

Dress the wheels

(

p.174)

SER

ANUAL

> IX. M

AINTENANCE

AND

SERVICING

171

Delta - Edging System > V1- 02-2020

Содержание DELTA




























































































































































































Результаты поиска

Содержание DELTA

Отзывы:

Essilor Instruments DELTA, Руководство пользователя, Страница: 168 / 187

Результаты поиска

Содержание DELTA

Отзывы: