Essilor Instruments DELTA Скачать руководство пользователя страница 169

Страница: 169 / 187

a. Precautions required

To avoid any incidents, unplug the device before all cleaning operation.

•

Clean the edger covers regularly: use a neutral detergent (e.g. washing-up liquid) diluted with water
on a soft cloth.

•

Clean the touch screen with a dry cloth: it must never be in contact with liquid (e.g. water, alcohol,
window cleaner).

•

Service the water recovery and filtration systems regularly.

•

Never clean the machine with chemicals (example: essences, diluents, solvents).

•

Never clean the machine elements (module, etc.) with a wet rag.

•

No additive should be added to the water in the edger tank. Do not add pyridine.

b. Clean the GCD module

From the working screen of the edger, select

to reach the cleaning menu.

The following screen is displayed:

Cleaning the module and trough

Close the door.

Press

to start the cleaning cycle.

> The cleaning is done automatically.

c. Remove and clean the window

Use a Phillips screwdriver to hand.

Unscrew the screw with a phillips screwdriver while holding the window.

Delta - Edging System > V1- 02-2020

172

SER

ANUAL

> IX. M

AINTENANCE

AND

SERVICING

Содержание DELTA




























































































































































































Результаты поиска

Содержание DELTA

Отзывы:

Essilor Instruments DELTA, Руководство пользователя, Страница: 169 / 187

Результаты поиска

Содержание DELTA

Отзывы: