Essilor Instruments DELTA Скачать руководство пользователя страница 121

Страница: 121 / 187

Indicate the size reduction to be applied to the lens you want to retouch.

The chosen finish and the modifications made during the edging cycle are automatically selected.

Insert the lens in the posiblock holder.

To close the clamp shafts manually, press and hold

Close the door.

Press

For a customized finish, the customized finish screen is displayed.

In all the other cases, the automatic tightening of the lens and the retouch start consecutively.

Select the second lens to be edged directly on screen, on the left or right of the work area.

The edging screen for the second lens is displayed.

All finishes chosen and the modifications made are kept. The retouch done on the first lens is

automatically saved for the edging of the second lens.

Delta - Edging System > V1- 02-2020

124

SER

ANUAL

> VII. E

DGING

LENS

Содержание DELTA




























































































































































































Результаты поиска

Содержание DELTA

Отзывы:

Essilor Instruments DELTA, Руководство пользователя, Страница: 121 / 187

Результаты поиска

Содержание DELTA

Отзывы: