Essilor Instruments DELTA Скачать руководство пользователя страница 45

Страница: 45 / 187

In the case of a demonstration lens or a recut lens, make sure that the marking feature is perfectly

horizontal to avoid any axis deviation during centering.

For more information, consult the section performing an optical tracing > Optical tracing > Prepare the

optical tracing of a demo lens or of recut lens.

(

p.28)

If need be, re-mark the points with a white colour gouache paint.

To center in re-marked micro-engravings mode

Pre-requisite: micro-engravings must be re-marked with a white felt tip pen. The diameter of the dots

must be between 0.5 and 1.5 mm.

We advise you to use the white felt tip marker supplied with the tracer-centerer-blocker to mark the

lens.

Description of the centering target

Optical center of the lens (orange cross) and boxing center of the shape (blue cross)

Centering marks

Centering the lens

Press

to select the type of single vision lens.

The centering target is displayed:

SER

ANUAL

> IV. C

ENTER

AND

BLOCK

LENS

Delta - Edging System > V1- 02-2020

Содержание DELTA




























































































































































































Результаты поиска

Содержание DELTA

Отзывы:

Essilor Instruments DELTA, Руководство пользователя, Страница: 45 / 187

Результаты поиска

Содержание DELTA

Отзывы: