Essilor Instruments DELTA Скачать руководство пользователя страница 175

Страница: 175 / 187

3. “T

RACER

CENTERING

DEVICE

BLOCKER

” F

UNCTION

Centering-blocking mode: boxing center (by default); optical center

Automatic initialization

Optical tracing:

•

tracing of tinted lenses

•

automatic tracing pattern, demo lens, recut lens in 2 dimensions

•

pre-positioning of drill-holes and their settings on a demo lens or a recut lens

•

recut lens: equivalent sphere [-1D; +1D]

The lenses with an infra-red filter cannot be read.

Manual centering:

•

single vision lenses: using focimeter dots or re-marked micro-engravings

•

progressive lenses: using re-marked micro-engravings or manufacturer markings

•

bifocal and trifocal lenses

•

executive lenses

•

mid-distance lenses: using re-marked micro-engravings or manufacturer markings

Centering help:

•

single vision lenses: partial or total detection of focimeter dots

Specific centering target for each type of lens: single vision, bifocal/trifocal, progressive, executive, mid-

distance

2-track optical video system: without parallax

Growing factor: x1.31 or x1.97

Input of job distances:

•

PD: 1/2 PD, ΔX

•

boxing height, Datum height, ΔY

•

modification by steps of 0.1 mm or 0.5 mm

Pantoscopic angle: from -5° to +25°

Shape modification:

•

scaling, A-dimension, B-dimension, ½ A-dimension, ½ B-dimension, D-dimension, one point
modification, rotation

•

retouch

•

modification by steps of 1 mm or 0.5 mm

Display of Precal dimensions

Toolbar customization

SER

ANUAL

> X. T

ECHNICAL

DATA

179

Delta - Edging System > V1- 02-2020

Содержание DELTA




























































































































































































Результаты поиска

Содержание DELTA

Отзывы:

Essilor Instruments DELTA, Руководство пользователя, Страница: 175 / 187

Результаты поиска

Содержание DELTA

Отзывы: