Essilor Instruments DELTA Скачать руководство пользователя страница 55

Страница: 55 / 187

Position the lens on the tube, with the convex side on the tube.

Move the lens slowly until it is perfectly centered:

•

Line up the transition segment between near vision and far vision with the horizontal mark in the
center

•

Position the central focimeter dot on the vertical axis of the target.

VISION

CENTERING

EAR

VISION

CENTERING

The lens is centered and ready to be blocked.

To block the lens, refer to the section Centering a lens > Blocking a lens

(

p.62)

6. C

ENTERING

MID

DISTANCE

LENS

Prerequisite: before carrying out lens centering, a shape must be displayed on the centering screen.

If necessary, we recommend that you first:

•

Modifying or retouching the traced shape

(

p.72)

•

Preparing the drilling points to be created (option)

(

p.82)

•

Place the stickers recommended by the manufacturer on hydrophobic lenses

(

p.62)

Concerning the use of the stickers, be careful to change the centering tube with a larger diameter one

to optimise the effectiveness of the sticker.

This section describes the procedures for centering a mid-distance lens:

•

Using re-marked micro-engravings

(

p.58)

•

Using manufacturer markings

(

p.60)

SER

ANUAL

> IV. C

ENTER

AND

BLOCK

LENS

Delta - Edging System > V1- 02-2020

Содержание DELTA




























































































































































































Результаты поиска

Содержание DELTA

Отзывы:

Essilor Instruments DELTA, Руководство пользователя, Страница: 55 / 187

Результаты поиска

Содержание DELTA

Отзывы: