Essilor Instruments DELTA Скачать руководство пользователя страница 102

Страница: 102 / 187

•

Press

to displace it towards the front surface of the lens.

•

Press

to displace it towards the rear surface of the lens.

The position of the bevel as well as the distances between the crest of the bevel and the front and

rear surfaces of the lens are displayed in the zoom window at the position of the cursor.

Close the door.

Press

The edging cycle starts.

When the edging cycle is finished, the retouch screen is displayed.

Press

to release the lens.

If necessary, retouch the lens.

Otherwise, start edging the second lens. Select the lens directly on the screen, on the left or right of the

work area.

The edging screen for the second lens is displayed. All finishes chosen and the modifications made

are kept.

g. Make a bevel/tilted groove

This function allows you to modify the bevel trajectory and/or groove according to:

1. A point on the lens, which will remain fixed and will not be parameterized (green square)
2. The opposite point (at 180°) that will be configurable (blue square)

Call the shape and select the custom mode

Press

to validate the choice.

SER

ANUAL

> VII. E

DGING

LENS

105

Delta - Edging System > V1- 02-2020

Содержание DELTA




























































































































































































Результаты поиска

Содержание DELTA

Отзывы:

Essilor Instruments DELTA, Руководство пользователя, Страница: 102 / 187

Результаты поиска

Содержание DELTA

Отзывы: