Essilor Instruments DELTA Скачать руководство пользователя страница 83

Страница: 83 / 187

b. Delete one drilling point

Select the drilling point to be deleted.

If you want to delete all drilling points from the shape, select any of them.

The drilling point is displayed in red.

Press

Two buttons are displayed:

Press:

•

to delete the selected drilling point, or

•

to delete all drilling points from the shape.

The selected drilling point or all drilling points are deleted from the shape.

c. Dimensioning a drilling point

You can define a setting for each existing drilling point.

Press on the drill-hole, slot or notch to select it.

The drilling point is displayed in red in the shape.

Press a few seconds on the setting to be modified:

•

Diameter

•

Depth (for non-through holes)

•

Length of slot or notch

•

Angle of slot or notch

The numeric keypad is displayed.

You can also use the

buttons to decrease or increase the selected value.

Enter the new value of the parameter and press

to confirm.

The drilling point has been modified.

Delta - Edging System > V1- 02-2020

SER

ANUAL

> VI. P

REPARING

DRILLED

JOB

Содержание DELTA




























































































































































































Результаты поиска

Содержание DELTA

Отзывы:

Essilor Instruments DELTA, Руководство пользователя, Страница: 83 / 187

Результаты поиска

Содержание DELTA

Отзывы: