manualshive.com logo in svg

Epson Stylus Photo R290, Руководство по обслуживанию, Страница: 34 / 125

Поделиться
Скачать
Epson Stylus Photo R290 Скачать руководство пользователя страница 34

EPSON Stylus Photo R280/R285/R290

Revision B

Chapter 3 Troubleshooting

3.3  Troubleshooting by Error Message

34

At power-on
During 
changing the 
platen gap

The error occurs when 
the PG (gap between 
the printhead surface 
and the platen) is 
changed with the APG 
Unit.

APG Unit

1. Is the APG Unit installed incorrectly?

1. Install the APG Unit carefully so as not to shift 

the phase.

4.4.4 “APG Unit”(p.75)

2. Is the Combination Gear 10,15.2 disengaged or 

attached incorrectly?

2. Attach the gear correctly.

APG Sensor Assy

1. Is the APG sensor damaged?

1. Replace the APG Sensor Assy.

4.4.16 “APG Sensor 
Assy”(p.91)

Any time

Other than above 
symptoms

Printhead

1. Is the Printhead damaged?

1. Replace the Printhead.

4.4.2 “Printhead”(p.72)

Main Board

1. Is the Main Board damaged?

1. Replace the Main Board.

4.3.1 “Main Board 
Unit”(p.61)

Table 3-6.  Troubleshooting for Cover Open Error

Occurrence 

Timing

Symptom

Failed Part

Check Point

Remedy

Reference

At power-on

The Printer Cover is 
closed, but the Cover 
Open error occurs.

Cover Open Sensor

1. Is the Cover Open Sensor cable not connected to 

CN17 on the Main Board?

1. Connect the cable to the connector on the Main 

Board.

4.3.2 “Panel Assy/ Cover 
Open Sensor”(p.64)

2. Is the Cover Open Sensor cable damaged?

2. Replace the Cover Open Sensor cable.

3. Is the Cover Open Sensor damaged?

3. Replace the Cover Open Sensor.

Table 3-5.  Troubleshooting for Fatal Error

Occurrence 

Timing

Symptom

Failed Part

Check Point

Remedy

Reference

Combination Gear

CR Motor

Содержание Stylus Photo R290






























































































































Отзывы:

Нет отзывов