Epson Stylus Photo R290 Скачать руководство пользователя страница 31

Страница: 31 / 125

EPSON Stylus Photo R280/R285/R290

Revision B

Chapter 3 Troubleshooting

3.3 Troubleshooting by Error Message

The following tables provide troubleshooting procedure for each error indicated by the LEDs or STM3 screen. When some parts need to be replaced or repaired, make sure to follow
the procedure given in Chapter 4 and carry out required adjustments.

3.3.1 Troubleshooting Problems with Error Messages

Table 3-4. Troubleshooting for Communication Error

Occurrence

Timing

Symptom

Failed Part

Check Point

Remedy

Reference

At power-on

The printer does not
work at all.

Panel Board/

Panel FFC

1. Is the Panel FFC not connected to the Panel Board

and CN5 on the Main Board?

1. Connect the FFC correctly.

4.3.2 “Panel Assy/
Cover Open
Sensor”(p.64)

2. Is the Panel FFC damaged?

2. Replace the Panel FFC.

3. Is the Panel Board damaged?

3. Replace the Panel Board.

P/S ASSY

1. Is the P/S ASSY connector cable not connected to

CN3 on the Main Board?

1. Connect the cable correctly.

4.3.3 “P/S Assy”(p.68)

2. Is the P/S ASSY cable or the P/S ASSY itself

damaged?

2. Replace the P/S ASSY.

* If this does not solve the problem, replace the

Main Board Assy.

USB cable

1. Is the USB cable not connected to the printer and

the PC?

1. Connect the USB cable correctly.

Printer driver

1. The printer driver installed on the PC is not the

one for the Stylus Photo R280/R285/R290?

1. Install the correct printer driver.

Main Board

1. The model name written into EEPROM on the

Main Board is wrong?

1. Write the correct model name to the EEPROM

using the Adjustment Program.

5.1.1 "Servicing
Adjustment Item List"
(P.96)

Содержание Stylus Photo R290






























































































































Результаты поиска

Содержание Stylus Photo R290

Отзывы:

Epson Stylus Photo R290, Руководство по обслуживанию, Страница: 31 / 125

Результаты поиска

Содержание Stylus Photo R290

Отзывы: