Epson Stylus Photo R290 Скачать руководство пользователя страница 45

Страница: 45 / 125

EPSON Stylus Photo R280/R285/R290

Revision B

Chapter 3 Troubleshooting

3.4 Troubleshooting by Symptom

Print quality problems

Table 3-16. Troubleshooting Print Quality Problems

Symptom

Possible Cause

Check Point

Remedy

Printed image has
missing colors,
and the missed
colors are always
same.

Dirt on the Printhead.

Run a cleaning cycle and make a test print. Repeat the operation
several times. Does the problem still appear?

Clean the Printhead surface with a cotton swab.

The absorber of the Cap Unit
contacts with the Printhead surface
during printing.

Is the absorber of the Cap Unit deformed or damaged?

Replace the Ink System.

Head FFC failure

Is the Head FFC damaged or broken?

Replace the Head FFC.

A malfunction of the Printhead

Run a cleaning cycle and print a nozzle check pattern. Repeat the
operation several times. Does the problem still appear?

Replace the Printhead.

Missing dots
appear
sometimes.

Dirt on the Printhead.

Run a cleaning cycle and print a nozzle check pattern. Repeat the
operation several times. Does the problem still appear?

Clean the Printhead surface with a cotton swab.

Ink cartridge failure

Replace the ink cartridge with a new one, and print a nozzle check
pattern. The printed pattern has no missing dots?

The cartridge is defective. Use the new cartridge.

Poor connection of the Head FFC

Check the FFC with a tester. Does the result show poor connection
of the FFC?

Replace the Head FFC.

A malfunction of the Printhead

Run a cleaning cycle and print a nozzle check pattern. Repeat the
operation several times. Does the problem still appear?

Replace the Printhead.

White streak /
abnormal
discharge

Poor connection of the Head FFC

Is the Head FFC not securely connected to the CR Unit and boards? Connect the FFC correctly.

A malfunction of the Printhead

Is the Head FFC not securely connected to the Printhead?

Connect the FFC correctly. If there is no problem with the connection
status, replace the Printhead.

Vertical lines are
misaligned.

Improper Bi-D adjustment

Using the Adjustment Program, check the Bi-D setting. Is the
setting made properly?

Carry out the Bi-D adjustment properly.

Содержание Stylus Photo R290






























































































































Результаты поиска

Содержание Stylus Photo R290

Отзывы:

Epson Stylus Photo R290, Руководство по обслуживанию, Страница: 45 / 125

Результаты поиска

Содержание Stylus Photo R290

Отзывы: