manualshive.com logo in svg

Epson Stylus Photo R290, Руководство по обслуживанию, Страница: 114 / 125

Поделиться
Скачать
Epson Stylus Photo R290 Скачать руководство пользователя страница 114

EPSON Stylus Photo R280/R285/R290

Revision B

Chapter 6 Maintenance

6.1  Overview

114

6.1.3  Lubrication

The type and amount of the grease used to lubricate the printer parts are determined 
based on the results of the internal evaluations. Be sure to apply the specified type and 
amount of the grease to the specified parts during servicing mentioned below.

†

When parts that need lubrication is been replaced

†

As the need arises during disassembly/reassembly of the printer

†

Refer to the following figures for the lubrication points.

LUBRICATION OF DRIVEN PULLEY

Figure 6-1.  Lubrication of Driven Pulley (1)

Figure 6-2.  Lubrication of Driven Pulley (2)

Figure 6-3.  Lubrication of Driven Pulley (3)

C A U T I O N

„

Never use oil or grease other than those specified in this manual. 
Use of different types of oil or grease may damage the component 
and adversely affect the printer operation.

„

Observe the specified amount. Never apply excess.

Table 6-1.  Specified Lubricant

Type

Name

EPSON code

Supplier

Grease

G-71

1304682

EPSON

Grease

G-77

1455324

EPSON

<Lubrication Points>
Four points where contact with the Main 
Frame

<Type>
G-71

<Application Amount>
ø 1 x 4 mm x 4 points

<Application Timing>
Apply before installing the Driven 
Pulley

<Remarks>
Apply with Injector

Application Point

Driven Pulley

<Lubrication Points>
Two points on bushings for the Pulley 
Shaft
One point at the center of the Pulley 
Shaft

<Type>
G-71

<Application Amount>
ø 1 x 1 mm x 3 points

<Application Timing>
Apply before installing the Driven 
Pulley

<Remarks>
Apply with Injector

<Lubrication Points>
Two points on the side of the Pulley

<Type>
G-71

<Application Amount>
ø 1 x 1 mm x 2 points

<Application Timing>
Apply after installing the Driven Pulley

<Remarks>
Apply with Injector

Application Point

Pulley Shaft

Driven Pulley

Driven Pulley Holder

Driven Pulley

Application Point

Driven Pulley Holder

Содержание Stylus Photo R290






























































































































Отзывы:

Нет отзывов