Epson Stylus Photo R290 Скачать руководство пользователя страница 59

Страница: 59 / 125

EPSON Stylus Photo R280/R285/R290

Revision B

Chapter 4 Disassembly/Assembly

4.2.3 Stacker Assy / Stacker Cover (Removing Exterior Parts/Components)

4.2.3 Stacker Assy / Stacker Cover

Parts/Components need to be removed in advance: Nothing

Removal procedure

Open the Stacker Cover.

Remove the Stacker Assy.

Release the Stacker Cover from the two shafts and remove the Stacker Cover.

Figure 4-12. Removing the Stacker Assy / Stacker Cover

4.2.4 Upper Housing

Parts/Components need to be removed in advance

Printer Cover / Paper Support Assy

Removal procedure

Remove the four screws and remove the Upper Housing upward.

•

Screw

: C.B.P. M3x10 (tightening torque: 5-7 kgf.cm)

(No.4)

(The numbers shown in the figure indicate the order of tightening the screws.)

Figure 4-14. Removing the Upper Housing

When installing the Stacker Assy, insert the guide pins of the
Stacker Assy into the lower grooves of the Guide Stacker Assy.
(The upper grooves are used when CDR is printed.)

Figure 4-13. Installing the Stacker Assy

Stacker Assy

Stacker Cover

Shaft

Groove

Guide Pin

Groove

[Rear Side]

Groove

Upper Housing

Содержание Stylus Photo R290






























































































































Результаты поиска

Содержание Stylus Photo R290

Отзывы:

Epson Stylus Photo R290, Руководство по обслуживанию, Страница: 59 / 125

Результаты поиска

Содержание Stylus Photo R290

Отзывы: