Epson Stylus Photo R290 Скачать руководство пользователя страница 66

Страница: 66 / 125

EPSON Stylus Photo R280/R285/R290

Revision B

Chapter 4 Disassembly/Assembly

4.3.2 Panel Assy/ Cover Open Sensor (Removing Control Boards)

Panel Board / Buttons Removal

Remove the Panel Assy.

(p.64)

Remove the screw of the Panel Unit.

•

Screw

: C.B.P. M3x10 (tightening torque: 3-5 kgf.cm)

(No.4)

Slide the Panel Unit in the upper right direction and remove it.

Figure 4-28. Removing the Panel Board / Buttons (1)

Disconnect the connector (CN1) on the Panel Board, peel the Panel FFC off
the back of the Panel Shield Plate, and remove the Panel FFC.

Remove the two screws and remove the Panel Shield Plate from the Panel
Unit.

•

Screw

: C.B.P. M3x10 (tightening torque: 3-5 kgf.cm)

(No.4)

Figure 4-29. Removing the Panel Board / Buttons (2)

Disengage the hook on the back of the Panel Board and remove the Panel
Board.

Figure 4-30. Removing the Panel Board / Buttons (3)

Release the liens from the guide pins of the Housing Panel B and remove the
sense from the Housing Panel B.

Disengage the nine hooks and remove the PS button, Ink button, and Paper
button.

Figure 4-31. Removing the Panel Board / Buttons (4)

[Rear Side]

Hook of the Panel

Shield Plate

Groove

Panel Unit

Open Sensor Holder

[Rear side]

Panel Shield Plate

Double-sided Tape

Reference Line

CN1

Panel FFC

Panel Unit

Panel Board

Hook

Positioning Hole

and Guide Pin

[Back Side]

Housing Panel B

Hook

[Back Side]

Guide Pins

Housing Panel B

Paper Button

Ink Button

PS Button

Lens

Содержание Stylus Photo R290






























































































































Результаты поиска

Содержание Stylus Photo R290

Отзывы:

Epson Stylus Photo R290, Руководство по обслуживанию, Страница: 66 / 125

Результаты поиска

Содержание Stylus Photo R290

Отзывы: