manualshive.com logo in svg

Epson Stylus Photo R290, Руководство по обслуживанию, Страница: 64 / 125

Поделиться
Скачать
Epson Stylus Photo R290 Скачать руководство пользователя страница 64

EPSON Stylus Photo R280/R285/R290

Revision B

Chapter 4 Disassembly/Assembly

4.3.2 Panel Assy/ Cover Open Sensor (Removing Control Boards)

64

4.3.2  Panel Assy/ Cover Open Sensor

†

Parts/Components need to be removed in advance

Printer Cover / Paper Support Assy / Housing Upper

†

Removal procedure

„

Panel Assy removal

1.

Peel off the acetate tape C.

2.

Disconnect the Panel FFC from the connector (CN5) on the Main Board and 
peel the Panel FFC off the Cable Holder Frame.

3.

Disconnect the CDR Sensor Cable and Cover Open Sensor Cable from the 
connectors (CN4, CN17) on the Main Board.

4.

Release the CDR Sensor Cable and Cover Open Sensor Cable from the two 
hooks of the Cable Holder Frame.

5.

Peel off the acetate tape A, B to separate the CDR Sensor Cable from the 
Cover Open Sensor Cable.

Figure 4-23.  Removing the Panel Assy (1)

6.

Remove the two screws.

•

Screw

 (3 pcs.): C.B.P. M3x6 (tightening torque: 5-7 kgf.cm) 

(No.1)

•

Screw

 (3 pcs.): C.B.P. M3x10 (tightening torque: 5-7 kgf.cm) 

(No.4)

7.

From the bottom of the Printer, insert a flathead screwdriver into the hole to 
disengage the tab, and remove the Panel Assy.

Figure 4-24.  Removing the Panel Assy (2)

CN4

CN17

CN5

Cover Open Sensor and 

CDR Sensor Cable

Hooks and Acetate Tape A, B

Double sided Tape

Main Board

Cable Holder 

Frame

Panel FFC

Acetate Tape C

C A U T I O N

When removing the screw (2) shown in 

Fig.4-24

, be careful not to 

damage the Cover Open Sensor Cable and CDR Sensor Cable.

Open Sensor Holder

Lower Housing

Tab

[Front side]

Disengage 

direction

Panel Assy

1

2

Содержание Stylus Photo R290






























































































































Отзывы:

Нет отзывов