Epson Stylus Photo R290 Скачать руководство пользователя страница 107 | Manualshive

Страница: 107 / 125

Epson Stylus Photo R290 Скачать руководство пользователя страница 107

EPSON Stylus Photo R280/R285/R290

Revision B

Chapter 5 Adjustment

5.3 Banding Reduction System (BRS) Adjustment / Paper Feed Amount Profile (PFP) Correction

107

5.3 Banding Reduction System (BRS) Adjustment /

Paper Feed Amount Profile (PFP) Correction

5.3.1 Overview

This section explains how to carry out BRS/PFP adjustments.

Tools and paper required to perform the adjustment

Specified Scanner to perform the adjustment

The following are the scanners that can be used for scanning the pattern in BRS/PFP
adjustment. When starting up the adjustment program, select the scanner to use.

Figure 5-11. System Configuration

C H E C K

P O I N T

For overview of BRS/PFP Adjustment,

refer to Chapter 2

Banding Reduction System (BRS) / Paper Feed Amount Profile
Correction (PFP)

Be sure to have a specified scanner ready beforehand as it is
necessary to carry out the adjustment. Before scanning,
confirm that the document table is free from any dirt or stain.

Table 5-6. Tools and Paper for BRS/PFP Adjustment

Tools/Paper

Product Code

Common

PFP Base scale

1453980

BRS

Matte Paper-Heavyweight

(A4)

---

PFP

Premium Glossy Photo Paper

(4 x 6)

---

C A U T I O N

Install the driver of the scanner to the PC in advance.

As the profile required for the adjustment is not prepared for
scanners other than the ones specified below, BRS/PFP
Adjustment can not be carried out by the other scanners.

Table 5-7. Specified Scanner for BRS/PFP Adjustment

Model Name

Sensor type

Remarks

Perfection 4990 Photo

CCD

Perfection V700 Photo

CCD

Stylus Photo RX560/RX580/RX590 CIS

Use the internal scanner.

Stylus Photo RX585/RX595/RX610 CIS

Use the internal scanner.

Stylus Photo RX680/RX685/RX690 CIS

Use the internal scanner.

C H E C K

P O I N T

Depending on the sensor type of the scanner to use for the
adjustment, drying time required after the BRS adjustment
pattern has been printed differs. For PFP adjustment pattern/PFP
check pattern, drying time is not required.

For “CCD” sensor:
Printed pattern can be scanned straight away. (Drying time of
about 2 minutes is recommended.)

For “CIS” sensor:
Printed pattern needs to be dried more than 5 minutes.

Calculate

correction

value

Test Pattern

Scanner

PC

Printer

«
...
105
106
107
108
109
...
»

Содержание Stylus Photo R290






























































































































Отзывы:

Нет отзывов