manualshive.com logo in svg

Epson Stylus Photo R290, Руководство по обслуживанию, Страница: 26 / 125

Поделиться
Скачать
Epson Stylus Photo R290 Скачать руководство пользователя страница 26

EPSON Stylus Photo R280/R285/R290

Revision B

Chapter 2 Operating Principles

2.3  Banding Reduction System (BRS) / Paper Feed Amount Profile Correction (PFP)

26

2.3  Banding Reduction System (BRS) / Paper Feed Amount Profile Correction (PFP)

†

Overview

In order to ensure high print quality and high print speed, this product incorporates the Banding Reduction System (BRS) and Paper Feed Profile (PFP) Correction system. The 
overview of them is described in the table below.

†

Adjustment/Correction method

Correction values of the BRS and the PFP are automatically calculated when a pattern printed by the printer is scanned by a specified scanner. The created correction 

values are stored into the serial flash ROM on the main board, and applied when printing in the target print mode. 

Table 2-6.  Overview of BRS and PFP

Summary

Target Print Mode

Remarks

Paper Type

Paper Size

Resolutions (dpi)

BRS

Conventional models perform overlapping printing (2-path or 4-
path print) to reduce banding problem. Printers that incorporate the 
Banding Reducing System do not perform the overlapping printing. 
They carry out 1-path printing correcting ink drop amount for each 
raster mode in order to avoid making a gap between each path 
(printed line). This enables to achieve both high print quality (less 
banding) and high print speed.

Ultra Glossy Photo Paper

Premium Glossy Photo Paper

Glossy Photo Paper

Premium Semigloss Photo Paper

4 x 6 inch

(102 x 152 mm)

720 x 720

---

PFP

In the conventional method to improve paper feed accuracy, the 
adjustment value is calculated based on a value obtained at a 
certain point of paper. Therefore, correcting the total paper feed 
amount (from when paper is fed and to when finishing printing) 
was impossible. The Paper Feed Amount Profile Correction offers 
more precise control over the paper feeding. Paper feed errors are 
measured at various points and a correction value is calculated for 
each of the points. This enables to ensure print quality in the target 
print mode.

Ultra Glossy Photo Paper

Premium Glossy Photo Paper

Glossy Photo Paper

Premium Semigloss Photo Paper

4 x 6 inch

(102 x 152 mm)

720 x 720

With BRS, Borderless print

720 x 360

Without BRS, 

Borderless print

A D J U S T M E N T

R E Q U I R E D

For information on how to carry out the BRS and PFP, 
See 

Chapter 5 Adjustment

.

Содержание Stylus Photo R290






























































































































Отзывы:

Нет отзывов