manualshive.com logo in svg

Epson Stylus Photo R290, Руководство по обслуживанию, Страница: 36 / 125

Поделиться
Скачать
Epson Stylus Photo R290 Скачать руководство пользователя страница 36

EPSON Stylus Photo R280/R285/R290

Revision B

Chapter 3 Troubleshooting

3.3  Troubleshooting by Error Message

36

Table 3-8.  Troubleshooting for Paper Jam Error

Occurrence 

Timing

Symptom

Failed Part

Check Point

Remedy

Reference

Any time

Even though the printer performs 
paper feeding operation, the paper is 
not fed into the printer.

ASF Unit

1. Is the ASF Unit installed incorrectly?

1. Install the ASF Unit correctly.

4.4.14 “ASF 
Unit”(p.88)

2. Is the Paper Return Lever not moving properly 

during the feeding operation?

2. Install the Paper Return Lever and the 

Torsion Spring 6.45 correctly.

Front Paper Guide 

Assy

1. Is the Torsion Spring 0.22 attached incorrectly? 

1. Install the PE Sensor Lever and Torsion 

Spring 0.22 correctly.

4.4.17 “Front Paper 
Guide Assy”(p.92)

Multiple sheets are fed at a time.

ASF Unit

1. Is the Retard Roller Assy not moving properly 

during the feeding operation?

1. Attach the Extension Spring 1.98 on the 

back side of the Retard Roller Assy 
correctly.

4.4.14 “ASF 
Unit”(p.88)

Paper is fed into the printer, but 
ejected at once without any printing 
operation.

PE Sensor

1. Is the PE sensor cable not connected to CN6 on 

the Main Board?

1. Connect the cable to the Main Board.

4.3.1 “Main Board 
Unit”(p.61)

1. Is the PE Sensor damaged?

2. Replace the PE Sensor.

4.4.17 “Front Paper 
Guide Assy”(p.92)

Torsion Spring 0.22

PE Sensor Lever

Extension 

Spring

ASF

Retard 

Roller

Содержание Stylus Photo R290






























































































































Отзывы:

Нет отзывов