Epson Stylus Photo R290 Скачать руководство пользователя страница 69

Страница: 69 / 125

EPSON Stylus Photo R280/R285/R290

Revision B

Chapter 4 Disassembly/Assembly

4.4.1 Removing the Printer Mechanism (Disassembling the Printer Mechanism)

4.4 Disassembling the Printer Mechanism

4.4.1 Removing the Printer Mechanism

Parts/Components need to be removed in advance

Printer Cover / Paper Support Assy / Upper Housing / Main Board Unit / Panel Assy /
Cover Open Sensor

Removal procedure

Disengage the hook of the Ink Tube Cover using a flathead screwdriver and
remove the Ink Tube Cover.

Figure 4-37. Removing the Ink Tube Cover

C A U T I O N

Be careful of the four sharp edges shown in the figure below
when assembling or reassembling.

Printer Mechanism Handling Precaution

When lifting the printer, hold

parts shown in the figure

below to prevent the frame from deforming.

Figure 4-35. Printer Mechanism Handling Precaution (1)

Sharp Edge

C A U T I O N

Do not touch the PF Scale with bare hands or damage it.

If the Printer Mechanism is tilted leftward about 15°, the PF
Scale hits against the desk surface and can break. After
removing the Printer Mechanism, take extra care to protect
the PF Scale.

Figure 4-36. Printer Mechanism Handling Precaution (2)

Print

er Me

chani

About

Do not tilt more than 15

degrees, or drag it while tilting.

Ribs

Hook

Ink Tube Cover

Содержание Stylus Photo R290






























































































































Результаты поиска

Содержание Stylus Photo R290

Отзывы:

Epson Stylus Photo R290, Руководство по обслуживанию, Страница: 69 / 125

Результаты поиска

Содержание Stylus Photo R290

Отзывы: