Epson Stylus Photo R290 Скачать руководство пользователя страница 40

Страница: 40 / 125

EPSON Stylus Photo R280/R285/R290

Revision B

Chapter 3 Troubleshooting

3.3 Troubleshooting by Error Message

Table 3-10. Troubleshooting for CD-R Tray Error

Occurrence

Timing

Symptom

Failed Part

Check Point

Remedy

Reference

When printing on
CDs/DVDs

The CDR Tray is set to the printer,
but the error occurs.

CDR Tray

1. Has the part of the CDR Tray that contacts with

the CDR Tray Sensor become cracked?

1. Replace the CDR Tray.

CDR Tray Sensor

1. Is the CDR Sensor cable not connected to CN4 on

the Main Board?

1. Connect the cable to the connector on

the Main Board.

4.4.18 “CDR
Tray
Sensor”(p.94)

4.3.1 “Main
Board
Unit”(p.61)

2. Is the CDR Tray Sensor damaged?

2. Replace the CDR Tray Sensor.

The CDR Tray center detection
sequence is interrupted, and the tray
is ejected.

CDR Tray

1. Is there any paper dust or foreign matter on the

white mark on the CDR Tray?

1. Remove any dust or foreign matter from

the tray.

CDR Tray

Contact point

White Mark

Содержание Stylus Photo R290






























































































































Результаты поиска

Содержание Stylus Photo R290

Отзывы:

Epson Stylus Photo R290, Руководство по обслуживанию, Страница: 40 / 125

Результаты поиска

Содержание Stylus Photo R290

Отзывы: